Lithium Ion

Ordering information:

• If you do not specify the configuration and plug, we will send flat pack without plug.
• We make custom battery packs. Please specify your need.
• Fax your sketch, if you can't find a suitable picture here.
• There is proper cooling air over the pack.
• All prices are for flat & hump packs; add $1.50 for all packs in stick configuration.
• Add $2.50 for installing Tamiya, Kyosho, mini Tamiya, mini Kyosho plugs.
• Add $3.50 for installing Anderson Power Pole (Sermos plug).
• Add $3.50 to include specific radio connector or BEC plug.
• Add $4.50 for installing Dean's Ultra plug.

Single Cells

LI-2400

(3.7V/mah) 2400; (Max Amp.**) 4.4;
(Size, mm) 18 dia x 65; (Wt, g) 44

Rtl

Sale

2LI-900

(7.2V/mah) 900; (Max Amp.**) 3.6;
(Size, mm) 30 x 47 x 17; (Wt, g) 48

2LI-2400

(7.4V/mah) 2400; (Max Amp.**) 4.8;
(Size, mm) 18 x 37 x 65; (Wt, g) 88

Rtl

Sale

3LI-900

(11.1V/mah) 900; (Max Amp.**) 3.6;
(Size, mm) 30 x 47 x 25; (Wt, g) 72

4-CELL PACK for Rx or Small Electric Planes

Rtl

Sale

4LI-2400

(7.4V/mah) 4800; (Max Amp.**) 9.6;
(Size, mm) 37 x 37 x 65; (Wt, g) 176

Safety Precautions for Lithium Polymer and Lithium Ion cells or battery packs
1. Never fast-charge any battery type unattended. 2. Never charge Li-Po & Li-ion cells/packs at any rate unattended. 3. Only charge Li-Po & Li-Ion cells/packs with a charger designed specifically for lithium polymer & lithium ion chemistry. 4. Li-Po & Li-Ion cells can ignite because of unmatched cell capacity or voltage, cell damage, charger failure, incorrect charger settings and other factors. 5. Always use the correct charging voltage. Li-Po & Li-Ion cells or battery packs may ignite if connected to a charger supplying more than 6 volts per cell. 6. Always assure the charger is working properly. 7. Always charge Li-Po & Li-Ion cells or battery packs where no harm can result, no matter what happens. We suggest a brick box or likeness. Have sand handy in a bucket for any need to extinguish any fire. NEVER use water on any cells or battery pack. 8. Never charge a cell/pack in a model. A hot pack may ignite wood, foam, plastic, etc. 9. Never charge a cell/pack inside a motor vehicle, or in a vehicle's engine compartment. 10. Never charge a cell/pack on a wooden workbench, or on any flammable material. 11. If a cell/pack is involved in a crash: a. Remove the cell or battery pack from the model. b. Carefully inspect the cell or battery pack for shorts in the wiring or connections. If in doubt, cut all wires from the cell or battery pack. c. Disassemble the pack. d. Inspect cells for dents, cracks and splits. Dispose of damaged cells (see below). 12. Dispose of cells or battery packs as follows: a. Discharge: with the cell or battery pack in a safe area, connect a moderate resistance across the terminals until the cell or battery pack is discharged. CAUTION: the cell or battery pack may be hot! b. Discard: puncture plastic envelope, immerse in salt water for several hours and place in regular trash. 13. Handle all cells or battery packs with care, as they can deliver high currents if shorted. Shorting by a wedding ring, for example, will remove a finger. 14. Always store cells or battery packs in a secure location where they cannot be shorted or handled by children. 15. When constructing a pack, use only cells of the same capacity (mAh).